✓ 연중무휴 하루 24시간 자동 온라인 주문 처리
✓ 풍부한 지식과 전문성을 갖춘 제품 및 기술 지원
✓ 신속하고 안정적인 (재)주문
Vortex Adapter for 24 (1.5–2.0 ml) tubes
카탈로그 번호 / ID. 13000-V1-24
For vortexing 1.5 and 2 ml tubes using the Vortex-Genie 2 Vortex.
로그인 계정 가격 보기.
forfortubes
24 x 1.5 – 2.0 ml
6 x 5 ml or 4 x 15 ml
2 x 50 ml
Vortex Adapters은/는 분자생물학 분야에 사용하기 위한 것입니다. 이 제품은 질병의 진단, 예방, 또는 치료용이 아닙니다.
✓ 연중무휴 하루 24시간 자동 온라인 주문 처리
✓ 풍부한 지식과 전문성을 갖춘 제품 및 기술 지원
✓ 신속하고 안정적인 (재)주문
특징
- Hands-free shaking of multiple tubes at the same time
- Maximized lysis with increased surface area in horizontal orientation
- Adapters connect directly to the Vortex-Genie 2 Vortex
- Available for microfuge, 5 ml, 15 ml and 50 ml tubes for unique applications
제품 세부 정보
Vortex Adapters conveniently maximize vortexing on the Vortex-Genie 2 Vortex and shake multiple tubes at the same time. Vortex Adapters hold tubes horizontally, which increases the contact surface area of beads and sample. Superior efficiency saves time and improves yield. Adapters are available for microfuge 1.7 or 2 ml tubes (cat. no. 13000-V1-24), 5 ml tubes (cat. no. 13000-V1-5) and 50 ml tubes (cat. no. 13000-V1-50) for bead beating, long mixing times or other unique applications.
Vortex Adapters are not recommended for use with temperatures below 4°C.
These adapters have been tested for use with tubes formerly marketed by MO BIO only.
절차
Before use, all adapters including the 3-inch platform head should be removed. To do this, grip the platform firmly with both hands and press upward, rocking back and forth to pop out the adapter. No special tools are required to remove the Vortex Adapter or the 3-inch platform head with nibs, however initial fit is very snug.
Adapters have a particular orientation: The bottom of the vortex adapter is a flat surface. Incorrectly orienting the adapter will damage it and may cause it to fail at high speeds, leading to loss of samples or injury. To install the adapter, align the flat surface with the flat side of the plastic nub on the Vortex-Genie 2. Pressing firmly straight down should snap it into place.
Tubes are always inserted into the clips with the cap facing the center of the adapter. The 1.5-2.0 ml tube adapters will click when the tubes slide in. Tubes need to be balanced when vortex is running, using a minimum of two tubes every time.
Adapters have a particular orientation: The bottom of the vortex adapter is a flat surface. Incorrectly orienting the adapter will damage it and may cause it to fail at high speeds, leading to loss of samples or injury. To install the adapter, align the flat surface with the flat side of the plastic nub on the Vortex-Genie 2. Pressing firmly straight down should snap it into place.
Tubes are always inserted into the clips with the cap facing the center of the adapter. The 1.5-2.0 ml tube adapters will click when the tubes slide in. Tubes need to be balanced when vortex is running, using a minimum of two tubes every time.
리소스
Safety Data Sheets (1)